Кулькові гвинти є найбільш часто використовуваними компонентами трансмісії в верстатах і точних машинах. Його основна функція полягає в перетворенні обертального руху в лінійний рух або перетворення крутного моменту в осьову повторювану силу. У той же час він також має характеристики високої точності, оборотності та високої ефективності.
Ексцентриситет: Відноситься до центрального відхилення між фіксованою стороною та опорною стороною.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60 м/хв, а примусове змащування масляним туманом можна вважати 60-100 м/хв. Рекомендується замовити порожнистий гвинт і застосувати примусове охолодження та змащення. Підтримуйте робоче середовище в чистоті та не допускайте потрапляння пилу та інших домішок у доріжку кочення або гайки. Якщо ситуація не найкраща, подумайте про додавання захисної кришки до гвинтів.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①Висока ефективність передачі. Ефективність передачі кульково-гвинтової передачі зазвичай становить 20,92-10 відсотків, а ефективність передачі звичайної ковзної гвинтової передачі становить 20,20-0.40.
②Висока точність передачі, стабільний рух і відсутність повзання. Кульково-гвинтовий привід – це в основному тертя кочення, з невеликим опором тертя, а опір тертя не має майже нічого спільного зі швидкістю руху.
③Робота на задній передачі без холостого ходу. Після того, як кульковий гвинт і гайка попередньо затягнуто{0}}, осьовий зазор можна усунути. Таким чином, у зворотному напрямку немає мертвої зони, а точність і жорсткість осьової передачі покращуються.
④Він оборотний. Оскільки втрати на тертя кульково-гвинтового ходу є малими, його можна перетворити з обертального руху в лінійний рух, а також його можна перетворити з лінійного руху в обертальний. Як ходовий гвинт, так і гайка можуть використовуватися як привід або супроводжувач.
⑤Тривалий термін служби. Завдяки малим втратам на тертя тертя кочення, термін служби тривалий.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
Зв'яжіться зараз
E-mail: sales@gyballscrew.com Tel(WhatsApp): плюс 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
